Fitting my Mulfab Brake Reaction Stays

Why Then Fit Brake Reaction Bars, Rods or Stays?

In my case it was because everyone who has already had them fitted recommends their effect on the handling under heavy braking. 

I personally have never had any complaint with 'The Green Goddess' over the 16k plus miles we have travelled together and yes, there have been one or two 'emergency stop' type braking incidents.

These Bars or Rods act to prevent twisting movement under Heavy Braking at the Top of the Morgan 'Cross Frame' which carries the Front Suspension.

This frame is not normally Braced at the Top End in the way that the Lower End is Firmly Braced.

I think that it is also true to say that almost all Morgan Race Cars have them fitted so that was good enough for me.

Some people have asked why the Factory do not fit them as standard? A Good Question. However, as may be clearly seen by this photo of a car in build below, they do fit them on some models or by request.

The 'Brake Reaction Rod' seen here between the Suspension Top to the Chassis (Sept 2011)

There are a variety of suppliers of these rods but I purchased mine from Williams Morgan as I was also purchasing another product from them. I subsequently discovered that they are actually manufactured by Peter Mulberry at Mulfab and are an  improvement on those shown in the Mulfab advert.

http://www.mulfab.co.uk/our-products/15/steering-suspension/cross-head-steady-bars

I was very pleasantly surprised when they arrived as they are made from 2mm Thick Walled Stainless Steel Tubing. 

They also benefit from a strengthened Top Lug where washers are Welded on and came complete with the correct sized fixing bolts and washers.

All I needed to do now was fit them.

 One Complete Set of Rod and Fixing Bolt

 The Top End Lug with Welded Washer

The Lower End with its fixing Nut & Bolt 

Fitting a Brake Reaction Rod

Due to the ease of access in my garage, I decided to fit the offside rod first.

Before Jacking the front end I needed to undo the Spinner. The car has just been serviced so the Spinner will be difficult to remove. 

I get out my trusty spanner, but have to take care as a 'nosebleed' resulted the last time I tried this so I had to revert to the rubber 'Wind Break' mallet.

Handbrake on and here goes.

My trusty MG Wing Nut Spanner Works a Treat this time. 

 I am only lifting the offside. The Trolley Jack goes under the Cross Member.

Up She Goes. 

The Trolley Jack stays in its Raised position throughout the job.

The Axle Prop is Placed near to this Offside 'Working' End.

The Lower Tie Rod can be seen in front of the Axle Prop.

The Nearside Lower Tie Rod. 
(The Large Plate seen Under the Chassis on the right is my Sump Guard & Deflector)

With the Wheel taken Off I now protect the Tread from Damage and 'Me' from a Grease Bath with this well used Plastic Bag & Tie.

Thread Protector

The Offside Suspension Top

A while ago I fitted a Remote Greasing System supplied by The Nipple Shop. I now need to remove the Feeder Pipe from the top of the suspension.  

Morgan Remote Greasing Kits

A few people have had problems with their pipes cracking. The trick is to have long pipes with gentle curves to spread the 'flexing' over a wide area.

My Protection Gaiter on the Top Spring appears to have slipped, but the spring is extending causing this effect so no problem. 

 A 12mm Spanner removes the pipe coupling.

 The Suspension Bolt is almost out. 

The Extracted Bolt showing the Grease Exiting its base.

The Suspension Top Bolt's Location (Nearside) 

I needed my trusty adjustable spanner to fit this one.

 With the Reaction Rod fitted onto the Top Bolt it is immediately apparent that the Wing Support Bracket needs to 'move over' a little. 

Releasing the bolt slightly and the Rod drops neatly into place.

Note the end of my Remote Greasing Pipe tucked behind the Damper Top

 Down at the Lower End I can now mark the position of the 12mm Hole that needs to be drilled in the Chassis. 

Shock & Horror, some would say. It is the only way to fit the rod! 

Note the little 'Cut Out' in the Chassis? 

This is there to prevent the Tyre Rubbing on the Chassis when the Steering is on maximum lock. Looking at older and different models these cut out vary in size. 

It is therefore important to ensure that the Rod is located hard against the upright.

 The All or Nothing Moment.

I drill a succession of four increasing passes to reach the correct size of hole remembering that occasional squirt of oil to help it on its way.

 The Bolt slips into the hole while the top end is still loose.

 Ready to lock down the Bolts and reconnect the Greasing Tube. 

Due to the extra thickness at the top end I need to re align the Grease Connection Block next.

 All is Tightened Down 

All of the Nuts & Bolts featured are now checked again for correct security

That is the Offside completed.

The Completed Nearside Rod Installation.

 A Squirt of Waxoil on the exposed New Parts will add more protection under there in the gloom and muck.

Frank

Fitting my Williams Morgan Lower Front Valance to The Green Goddess

Why fit a Lower Valance you may ask.

My Original Morgan Radiator, which has a Plastic Body and Connection Lugs,  sheared its lower pipe connection, a problem proving to be quite common to these radiators. It sheared just as I arrived at the Dealership on the day that it was due to have its Annual Service and MOT Test. 

Rather than replace the Radiator with another original plastic one I decided to invest in an Aluminium Radiator made by Aftersales Specialist Peter Mulberry, ( Mulfab).

Mulfab Aluminium Radiators

The Mulfab Radiator is larger and deeper than the original Morgan version providing a for more efficient cooling. It does however, hang down lower below the Front End than the original one did before

Initially I had sprayed the lower edge box part of the Radiator but despite dulling the bright finish, the lower edge was still obvious. It needed a Valance of some sort to cover it.

 The Mulfab Radiator Base.

  

I purchased this Lower Valance when I heard that another Roadster 100 Register Member was having both an Aluminium Radiator and a Lower Valance fitted to his car at Williams Morgan.

I was hoping to get mine made and painted at the same time and then delivered for me to fit myself. It could not be that difficult, could it? 

Our Register Members Williams Lower Valance in place.

Williams Morgan

My Valance arrived some months later but I first needed to build a Workbench in my newly refurbished Garage before I started the job. 

This Work bench was completed on Friday so I set to and stripped off the Number Plate and removed the Grill to find out where to go next.

Unfortunately the delivered Valance only came with a Bag of Six Bolts with Nuts and Washers and Two Strips of Aluminium Bar with a hole drilled in one end of each one.

 The New Valance

One of the Aluminium Bars

Bag of Bolts, Washers & Nuts

And So the Mystery began. 

Under the Front End there are Two Bolts protruding inwards which hold the lover ends of the Radiator Cowl to the Chassis. These two Cross Head bolts are the same size as two of the new bolts supplied. 

There was sufficient excess thread to carry both the Cowl, the Valance and its inside and outside washers and nut without needing to remove the existing nut & bolt. 

The Two Slotted Holes already in my New Valance obviously should have lined up with these bolt ends but, being on a Hand Built Morgan, needless to say, the Slots were slightly too far apart. 

I set too using one of my small Tapered Grindstones and soon the slots were rounded to provide the very width that I needed.

 The Rounded Hole 

(with lots of messy transfer of chassis Wax Oil from my hands.)

However, The Valance still would not fit. I then realised that the Twin Horns, which are located below the Chassis Radiator Opening, were also in the way.

After some Head Scratching, I realised that the Horns would have to be removed or repositioned.  
With some redirecting of the Power Cables, the Two Horns are now located above the Chassis inside the Radiator Box and behind the Grill rather than behind the Number Plate. 

Rather than have the Horns facing forward as before, allowing water to run down inside, I have turned them sideways. I also wrapped the Cables with Black Insulating Tape to tidy the appearance.

   The Twin Horns now set above the Chassis

At this point in the proceedings I spent quite a while under the car with my inspection lamp wondering where these two pieces of Aluminium Bar would be used and what they would fit to as there were no more holes in the New Valance and only one hole in each aluminium bar.

I needed to sleep on this one. I had thought of emailing our member to ask him for some photos of his installation. I even thought of contacting Williams.  

This morning I took another look under and realised that there were now two threaded bolts hanging down from the Chassis - Under the Two Horns! 

Suddenly realisation took place as these could be the location for one end of the Aluminium Bars. Again the exposed Threaded Horn Bolts would be long enough to take the 2.5mm thick Aluminium Bar, Locking Washers and Nuts.

I cut a Card Template exactly the same size as one of the Aluminium Bars and Temporarily fitted the Valance again onto its two existing bolt ends.  

Working back from the Lower ends of the Horn Bolts I folded two angles into the Card Strip. The Top End is to the left.

My Card Template with Folds and Hole Positions Marked.

The two Horn Bolt Ends are set 15cm apart. All I now needed to do was drill Two Extra Holes in the Bars sized to Fit the Horn Bolts and then to drill Two Extra Holes 15cm apart in the Upturned inner edge of the Cowl.

Two Holes Drilled in The Cowl Upturn

(Masking Tape used to protect the Paintwork)

The Next Task was to bend the Aluminium Bars to the same shape as my Card Template. I needed the use of my New Vice on my New Bench to complete this task efficiently.

 First Bend Completed  

 Both Bends Completed

Compared to the Card Template

Before Fitting the Valance permanently to the Body Bolts I first needed to fit these Brackets to the Horn Bolts permanently.

 The Completed Brackets fitted to the Horn Bolts 

One of the Brackets - and my Painted Radiator Base 

Now the Valance has to be permanently fitted to their existing Bolt Ends. But first I would polish off all of those greasy Wax Oil finger marks.

I decided not to use the New Cross Head Bolts supplied with the Valance as to replace the whole bolt could prove very difficult and it was not essential as there was enough exposed thread on the existing Bolt to carry the Valance and the Nut & Washers.  

I would use the Two Large Washers supplied, one inside and one outside, and the Self Locking Nuts, one on each side

The Attached Valance on the Existing Cross Head Bolt End.

This photo appears strange due to the reflections inside of the Valance. 

It shows where I have attached the New 10mm Bolts and their pair of Washers between the lower end of the Aluminium Brackets and the Upturn provided on the New Valance, where I drilled the two new holes. 

 This is the Upturn showing one of the 10mm Bolt Heads and the Outside Washer.

 This one shows the Upper end of the Brackets and one of the other fixing points.

After a bit of a struggle to get the Grill back into its slot and onto the Bolt Pegs, The Badge Bar and the Number Plate Box are both back in place. 

Now I just have to find that 'safe place' where I put the Number Plate Screws.

Number Plate Back On the Car - Job Done! 

 The Full Valance, photo taken from Lower Down.

Then a Squirt of Wax Oil on the new Nuts and Bolts to complete this task.

For Next Time. I also bought as set of  Williams Morgan's Reactions Brake Reaction Rods with the Cowl, so I need to set about Planning to fix those in place but could prove a little more challenging for me.
Frank. 

My Roadster 100 Calendar for 2016

Every Year since the setting up of our Morgan Centenary Roadster 100 Register I have published a Calendar.

Last year 16 other Members purchased a Calendar. Since then 6 of them have sold their cars and I suspected that interest from other members may be waning. 

This year I would only have three copies made and use them to test the water. 

True to expectations I only managed to sell two of them for donations to our chosen charity, Combat Stress 

Here are the Front Cover and the Monthly Pages with Photos